Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-74

System Events

Warning e-mail is sent when…

Switch Cold Start

Power is cut off and then reconnected.

Switch Warm Start

The EDS is rebooted, such as when network
parameters are changed (IP address, subnet mask,
etc.).

Power Transition (On



Off)

The EDS is powered down.

Power Transition (Off



On)

The EDS is powered up.

DI1 (On



Off)

Digital Input 1 is triggered by on to off transition

DI1 (Off



On)

Digital Input 1 is triggered by off to on transition

DI2 (On



Off)

Digital Input 2 is triggered by on to off transition

DI2 (Off



On)

Digital Input 2 is triggered by off to on transition

Configuration Change Activated

A configuration item has been changed.

Authentication Failure

An incorrect password is entered.

Comm. Redundancy Topology
Changed

Spanning Tree Protocol switches have changed their
position (applies only to the root of the tree).
The Master of the Turbo Ring has changed or the
backup path is activated.

Port Events

Warning e-mail is sent when…

Link-ON

The port is connected to another device.

Link-OFF

The port is disconnected (e.g., the cable is pulled out,
or the opposing device shuts down).

Traffic-Overload

The port’s traffic surpasses the Traffic-Threshold for
that port (provided this item is Enabled).

Traffic-Threshold (%)

Enter a non-zero number if the port’s
Traffic-Overload item is Enabled.

Traffic-Duration (sec.)

A Traffic-Overload warning is sent every

Traffic-Duration

seconds if the average

Traffic-Threshold is surpassed during that time
period.

NOTE

The

Traffic-Overload

,

Traffic-Threshold (%)

, and

Traffic-Duration (sec.)

Port Event items

are related. If you Enable the Traffic-Overload event, then be sure to enter a non-zero
Traffic-Threshold percentage, as well as a Traffic-Duration between 1 and 300 seconds.

NOTE

Warning e-mail messages will have the

sender

field formatted

in the form:

Moxa_EtherDevice_Switch_0001@Switch_Location

where

Moxa_EtherDevice_Switch

is the default Switch Name,

0001

is the EDS’s serial number,

and

Switch_Location

is the default Server Location.

Refer to the Basic

Settings

section to see how to modify Switch Name and Switch Location.

«
...
87
88
89
90
91
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

Enterprise Filter Authentication R3000

Бренд: 8e6 Technologies Страницы: 66

PG-FlexPlus AMU-912

Бренд: ADC Страницы: 130

Бренд: Fieldbus Specialists Страницы: 39

Бренд: ZyXEL Communications Страницы: 116

IBOX-BAC Series

Бренд: IntesisBox Страницы: 2

WRT54GR - Wireless-G Broadband Router

Бренд: Linksys Страницы: 81

Бренд: Idis Страницы: 17

IGS-5225-20T4C2X

Бренд: Planet Страницы: 16

Бренд: Ista Страницы: 16

Бренд: Sierra Wireless Страницы: 2

OmniTik UPA-5HnD

Бренд: RouterBOARD Страницы: 4

AMSTX-CF Series

Бренд: ADLINK Technology Страницы: 73

Broadband 700 MHz

Бренд: Alcatel-Lucent Страницы: 8

WISENET XRN-1610

Бренд: Hanwha Techwin Страницы: 88

Бренд: Aztech Страницы: 13

Бренд: Tripp Lite Страницы: 3

Бренд: Abov Страницы: 8

Бренд: Boardcon Embedded Design Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды