Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 110

Страница: 110 / 129

EDS-508A/505A Series User’s Manual

EDS Configurator GUI

4-5

Click the

Upgrade Firmware

toolbar icon

, or select

Upgrade

under the

Firmware

menu.

If the switch is Locked, you will be prompted to input the switch’s User Name and Password.

Use the

Open

window to navigate to the folder that contains the firmware upgrade file, and

then click the correct “*.rom” file (

eds.rom

in the example shown below) to select the file.

Click

Open

to activate the upgrade process.

Modify IP Address

You may use the Modify IP Address function to reconfigure the EDS’s network settings. Start by

clicking the Modify IP address icon

, or by selecting

Modify IP address

under the

Configuration

menu.

The

Setup Configuration

window will open. Checkmark the box to the left of those items that

you wish to modify, and then Disable or Enable DHCP, and enter IP Address, Subnet mask,
Gateway, and DNS IP. Click

to accept the changes to the configuration.

Содержание EDS-505A Series


































































































































Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды

Moxa Technologies EDS-505A Series, Руководство пользователя

Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды