Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-36

Setting

Description

Factory Default

Enable

Select this EDS as Coupler

Disable

Do not select this EDS as Coupler

Not checked

Coupling Mode

Setting

Description

Factory Default

Dual Homing

Select this item to change to the
Dual Homing configuration page

EDS-508A
Primary Port:

port 5

Backup Port:

port 6

EDS-505A
Primary Port:

port 2

Backup Port:

port 3

Ring Coupling
(backup)

Select this item to change to the
Ring Coupling (backup)
configuration page

EDS-508A: Port 5
EDS-505A: Port 2

Ring Coupling
(primary)

Select this item to change to the
Ring Coupling (primary)
configuration page

EDS-508A: Port 5
EDS-505A: Port 2

Primary/Backup Port

Setting

Description

Factory Default

Primary Port

Select any port of the EDS to be the
primary port.

EDS-505A: port 2
EDS-508A: port 5

Backup Port

Select any port of the EDS to be the
backup port.

EDS-505A: port 3
EDS-508A: port 6

NOTE

The Turbo Ring DIP Switches located on the
EDS-508A/505A’s outer casing can be used to
configure the EDS’s Turbo Ring protocols. (For
details on how to do this, refer to “Configuring Basic
Settings—Turbo Ring DIP Switch” section in this
manual.)

If you use the web interface, console interface, or
Telnet interface to enable the Turbo Ring DIP
Switches, and then set DIP Switch 4 on the switch’s
outer casing to the “ON” position, you will not be able
to use the web interface, console interface, or Telnet
interface to change the status of the DIP Switch. In
this case, the

Communication Redundancy

settings

will be “grayed out” in the web browser as shown in
the following figure:

The Turbo Chain Concept

«
...
49
50
51
52
53
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

Бренд: D-Link Страницы: 267

AirPlus DWL-810

Бренд: D-Link Страницы: 25

Бренд: GE Страницы: 146

TokenLink Velocity 3C319

Бренд: 3Com Страницы: 2

Enterprise Filter Authentication R3000

Бренд: 8e6 Technologies Страницы: 66

Бренд: Alesis Страницы: 61

Бренд: Buffalo Страницы: 2

EK-Loop Modulus Series

Бренд: ekwb Страницы: 7

VMG5313-BXB SERIES

Бренд: ZyXEL Communications Страницы: 2

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

Бренд: Nortel Страницы: 163

Бренд: Baracoda Страницы: 16

DAS-1800HR Series

Бренд: Keithley Страницы: 139

Бренд: Laser Страницы: 4

Бренд: ST Страницы: 67

Бренд: Promise Technology Страницы: 148

Бренд: Socket Страницы: 18

Бренд: BOSER Technology Страницы: 78

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды