Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-82

Perform the following steps to set up the

Mirror Port

function:

STEP 1

Configure the EDS’s

Mirror Port

function from either the Console utility or Web Browser

interface. You will need to configure three settings:

Monitored Port

Select the port number of the port whose network activity will be
monitored.

Mirror Port

Select the port number of the port that will be used to monitor the
activity of the monitored port.

Watch Direction

Select one of the following three watch direction options:



Input data stream

Select this option to monitor only those data packets coming

in

through

the EDS’s port.



Output data stream

Select this option to monitor only those data packets being sent

out

through

the EDS’s port.



Bi-directional

Select this option to monitor data packets both coming

into

, and

being sent

out through

, the EDS’s port.

STEP 2

Be sure to activate your settings before exiting.



When using the Web Browser interface, activate by clicking

Activate

.



When using the Console utility, activate by first highlighting the Activate menu option, and
then press

Enter

. You should receive the

Mirror port settings are now active! (Press any key

to continue)

message.

Ping

The

Ping

function uses the

ping

command to give users a simple but powerful tool for

troubleshooting network problems. The function’s most unique feature is that even though the
ping command is entered from the user’s PC keyboard, the actual ping command originates from
EDS itself. In this way, the user can essentially control the EDS and send ping commands out
through its ports.

To use the Ping function, type in the desired IP address, and then press

Enter

from the Console

utility, or click

Ping

when using the Web Browser interface.

«
...
95
96
97
98
99
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

FrameSaver 9120

Бренд: Paradyne Страницы: 2

EK-FC780 GTX Jetstream

Бренд: ekwb Страницы: 2

Бренд: Niveo Страницы: 155

NetStructure ZT 5515

Бренд: Intel Страницы: 90

Бренд: Furuno Страницы: 24

Бренд: SIIG Страницы: 12

Бренд: WaiLan Страницы: 27

Бренд: EVS Страницы: 30

Бренд: SIIG Страницы: 6

Бренд: Toto Link Страницы: 55

Бренд: ebm-papst Страницы: 11

Бренд: YASKAWA Страницы: 15

Бренд: DAD Страницы: 16

Бренд: Addonics Technologies Страницы: 1

Бренд: National Instruments Страницы: 130

HHM Series HHM2245SA1

Бренд: TDK Страницы: 2

Бренд: H3C Страницы: 9

Бренд: JUMO Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды