Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 21

Страница: 21 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-6



Any host can access the EDS

Disable this function by deselecting the

Enable the accessible IP list

option.

The following table shows additional configuration examples:

Allowable Hosts

Input format

Any host

Disable

192.168.1.120 192.168.1.120

255.255.255.255

192.168.1.1 to 192.168.1.254

192.168.1.0 / 255.255.255.0

192.168.0.1 to 192.168.255.254

192.168.0.0 / 255.255.0.0

192.168.1.1 to 192.168.1.126

192.168.1.0 / 255.255.255.128

192.168.1.129 to 192.168.1.254

192.168.1.128 / 255.255.255.128

Port

Port

settings are included to give the user control over Port Access, Port Transmission Speed,

Flow Control, and Port Type (MDI or MDIX). An explanation of each configuration item follows:

Enable

Setting

Description

Factory Default

checked

Allows data transmission through the port.

unchecked

Immediately shuts off port access.

enabled

ATTENTION

If a connected device or sub-network is wreaking havoc on the rest of the network, the

Disable

option under

Advanced Settings/Port

gives the administrator a quick way to shut off access

through this port immediately.

Содержание EDS-505A Series


































































































































Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды

Moxa Technologies EDS-505A Series, Руководство пользователя

Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды