Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-14

Disable the Turbo Ring DIP Switch

Setting

Description

Factory Default

Enable the Turbo
Ring DIP
Switches

The four DIP switches are

enabled

when the

“Disable the Turbo Ring DIP Switch” box is
not checked.

Disable the Turbo
Ring DIP
Switches

The four DIP switches are

disabled

when the

“Disable the Turbo Ring DIP Switch” box is
checked.

Not checked (i.e., the
Turbo Ring DIP Switches
are enabled by default)

Set DIP switch as Turbo Ring / Set DIP switch as Turbo Ring V2

Setting

Description

Factory Default

Set DIP switch as
Turbo Ring

Select this option to enable the Turbo Ring DIP
switches to configure the EDS for a “Turbo
Ring” ring.

This is the default if you do
NOT reset the switch to
factory default settings
(provided you upgraded the
firmware for Turbo Ring
V2).

Set DIP switch as
Turbo Ring V2

Select this option to enable the Turbo Ring DIP
switches to configure the EDS for a “Turbo
Ring V2” ring.

This is the default if you
DO reset the switch to
factory default settings
(provided you upgraded the
firmware for Turbo Ring
V2).

NOTE

If you upgrade the firmware of your EDS from Turbo Ring to Turbo Ring V2, but do not reset the
switch to factory defaults, the DIP switches will be set to configure the EDS for a “Turbo Ring”
ring. If you reset the switch to factory defaults, the DIP switches will be set to configure the EDS
for a “Turbo Ring V2” ring.

How to Configure the Turbo Ring DIP Switches

The Turbo Ring DIP Switches are set to the OFF position at the factory.

NOTE

The four DIP Switches are used to configure both the “Turbo Ring”
and “Turbo Ring V2” protocols, depending on which protocol is
active. To select which protocol the EDS will use, start the user
interface software, and then use the left menu to navigate to the

Communication Redundancy

page. To use one of the Turbo Ring

protocols for the EDS, select either “Turbo Ring” or “Turbo Ring V2”
in the

Redundancy Protocol

drop-down box. See the

Configuring

“Turbo Ring” and “Turbo Ring V2”

section in this chapter for

details.

12

------

MASTER

COUPLER

TURBO
RING

34

The following tables show how to use the DIP switches to configure the EDS for “Turbo Ring” or
“Turbo Ring V2.”

NOTE

DIP switch 4 must be set to the ON position to enable DIP switches 1, 2, and 3. If DIP switch 4 is
set to the “OFF” position, then DIP switches 1, 2, and 3 will all be disabled.

«
...
27
28
29
30
31
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Бренд: D-Link Страницы: 53

Бренд: Ebyte Страницы: 14

Бренд: Hawking Страницы: 2

Бренд: STONEFLY Страницы: 48

Бренд: ZALMAN Страницы: 4

Бренд: Renesas Страницы: 20

Бренд: Teletronics International Страницы: 57

ConnectX-3 Pro MCX349A-XCCN

Бренд: Mellanox Technologies Страницы: 35

Бренд: Idis Страницы: 17

IGS-5225-20T4C2X

Бренд: Planet Страницы: 16

Бренд: FiberHome Страницы: 2

Powereta iQP Series

Бренд: TDK Страницы: 2

Бренд: ZyXEL Communications Страницы: 2

Бренд: TRENDnet Страницы: 68

Бренд: ZALMAN Страницы: 9

Бренд: Eaton Страницы: 32

CNPS8900 Series

Бренд: ZALMAN Страницы: 10

PXI Express PXIe-1085 Series

Бренд: National Instruments Страницы: 89

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды