Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 129

background image

EDS-508A/505A Series User’s Manual

Introduction

1-3

Package Checklist

The Moxa EtherDevice Switch EDS-508A/505A Series is shipped with the following items. If any
of these items are missing or damaged, please contact your customer service representative for
assistance.



1 Moxa EtherDevice Switch EDS-508A/505A



Hardware Installation Guide



CD-ROM with User’s Manual and Windows Utility



Moxa Product Warranty booklet



RJ45 to DB9 Console port cable



Protective caps for unused ports



Panel mounting kit (optional

—

must order separately)

Features



IPv6 Ready logo awarded (IPv6 Logo Committee certified).



IEEE 1588 PTP (Precision Time Protocol) for precise time synchronization of networks.



DHCP Option 82 for IP address assignment with different policies.



Modbus/TCP industrial Ethernet protocol supported.



Turbo Ring and Turbo Chain (recovery time < 20 ms at full load) and RSTP/STP (IEEE

802.1w/D).



IGMP snooping and GMRP for filtering multicast traffic.



Port-based VLAN, IEEE 802.1Q VLAN, and GVRP to ease network planning.



QoS (IEEE 802.1p/1Q) and TOS/DiffServ to increase determinism.



Port Trunking for optimum bandwidth utilization.



IEEE 802.1X, HTTPS, and SSH to enhance network security.



SNMPv1/v2c/v3 for different levels of network management.



RMON for efficient network monitoring and proactive capability.



Bandwidth management prevents unpredictable network status.



Lock port function for blocking unauthorized access based on MAC address.



Port mirroring for online debugging.



Automatic warning by exception through e-mail, relay output.



Digital inputs to integrate sensors and alarms with IP networks.

«
...
5
6
7
8
9
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

Бренд: Lauterbach Страницы: 61

Бренд: Raritan Страницы: 4

RDX QuikStation 4

Бренд: Tandberg Data Страницы: 2

INTERNET PRIVACY PROTECTION

Бренд: AlphaShield Страницы: 49

Бренд: Konig Страницы: 73

Armor 101 Series

Бренд: Lochinvar Страницы: 28

Armor 101 Series

Бренд: Lochinvar Страницы: 44

Asynchronous SH7145F

Бренд: Renesas Страницы: 17

Бренд: Qixiang Technology Страницы: 16

Hollywood DV-Bridge

Бренд: Dazzle Страницы: 63

Бренд: H3C Страницы: 12

Бренд: Patton electronics Страницы: 12

Бренд: TP-Link Страницы: 2

Бренд: National Instruments Страницы: 8

Бренд: QNAP Страницы: 54

Бренд: ZALMAN Страницы: 9

Бренд: Belkin Страницы: 2

Бренд: Pressalit Care Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды