Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-16

NOTE

If you use the browser interface to enable the DIP switches (by un-checking the “Disable the
Turbo Ring DIP switch” checkbox), and then flip DIP switch 4 from

ON

to

OFF

, the Ring Ports

and Coupling Ports that were added to all VLANs will be restored to their previous software
settings. (For details, please refer to the “Using Virtual LANs” section of this manual).

System File Update—By Remote TFTP

The EDS supports saving your configuration file to a remote TFTP server or local host to allow
other EDS switches to use the same configuration at a later time, or saving the Log file for future
reference. Loading pre-saved firmware or a configuration file from the TFTP server or local host
is also supported for easy upgrading or configuration of the EDS.

TFTP Server IP/Name

Setting

Description

Factory Default

IP Address of TFTP
Server

The IP or name of the remote TFTP server. Must be
set up before downloading or uploading files.

None

Configuration Files Path and Name

Setting

Description

Factory Default

Max. 40 Characters

The path and file name of the EDS’s configuration
file in the TFTP server.

None

Firmware Files Path and Name

Setting

Description

Factory Default

Max. 40 Characters

The path and file name of the EDS’s firmware file.

None

Log Files Path and Name

Setting

Description

Factory Default

Max. 40 Characters

The path and file name of the EDS’s log file

None

After setting up the desired path and file name, click

Activate

to save the setting, and then click

Download

to download the prepared file from the remote TFTP server, or click

Upload

to upload

the desired file to the remote TFTP server.

«
...
29
30
31
32
33
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

Бренд: NEC Страницы: 47

Express5800/E120d-M

Бренд: NEC Страницы: 2

Power Xpert Meter 2000

Бренд: Eaton Страницы: 16

POW-R-COMMAND 1000

Бренд: Eaton Страницы: 84

Бренд: IDT Страницы: 281

DMX-Universal-Demux

Бренд: DMX4ALL Страницы: 17

Бренд: Rockwell Automation Страницы: 108

Sentry Global Security Modem

Бренд: Server Technology Страницы: 22

Бренд: Commell Страницы: 9

Бренд: TP-Link Страницы: 2

Бренд: E-Lins Страницы: 113

Бренд: Omron Страницы: 13

Бренд: BWI Страницы: 5

Бренд: Nilox Страницы: 66

Бренд: ZiLOG Страницы: 11

Бренд: ADTRAN Страницы: 4

Developer's Board

Бренд: Sony Ericsson Страницы: 28

TeraBridge 5845

Бренд: Proxim Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды