Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 32

Страница: 32 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-17

System File Update—By Local Import/Export

Configuration File

To export the configuration file of this EDS, click

Export

to save it to the local host.

Log File

To export the Log file of this EDS, click

Export

and save it to the local host.

NOTE

Some operating systems will open the configuration file and log file directly in the web page. In
such cases, right click

Export

to save as a file.

Upgrade Firmware

To import the firmware file of this EDS, click

Browse

to select the firmware file already saved on

your computer. The upgrade procedure will proceed automatically after clicking

Import

Upload Configuration Data

To import the configuration file of this EDS, click

Browse

to select the configuration file already

saved on your computer. The upgrade procedure will proceed automatically after clicking

Import

Содержание EDS-505A Series


































































































































Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды

Moxa Technologies EDS-505A Series, Руководство пользователя

Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды