Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 48

Страница: 48 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-33

Redundancy Protocol

Setting

Description

Factory Default

Turbo Ring

Select this item to change to the Turbo
Ring configuration page.

Turbo Ring V2

Select this item to change to the Turbo
Ring V2 configuration page.

Turbo Chain

Select this item to change to the Turbo
Chain configuration page

RSTP (IEEE
802.1W/1D)

Select this item to change to the RSTP
configuration page.

None

Ring redundancy is not active

None

Set as Master

Setting

Description

Factory Default

Enabled

Select this EDS as Master

Disabled

Do not select this EDS as Master

Not checked

Redundant Ports

Setting

Description

Factory Default

1st Port

Select any port of the EDS to be one
of the redundant ports.

EDS-505A: port 4
EDS-508A: port 7

2nd Port

Select any port of the EDS to be one
of the redundant ports.

EDS-505A: port 5
EDS-508A: port 8

Enable Ring Coupling

Setting

Description

Factory Default

Enable

Select this EDS as Coupler

Disable

Do not select this EDS as Coupler

Not checked

Coupling Port

Setting

Description

Factory Default

Coupling Port

Select any port of the EDS to be the
coupling port

EDS-505A: port 2
EDS-508A: port 5

Coupling Control Port

Setting

Description

Factory Default

Coupling Control Port

Select any port of the EDS to be the
coupling control port

EDS-505A: port 3
EDS-508A: port 6

Configuring “Turbo Ring V2”

Содержание EDS-505A Series


































































































































Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды

Moxa Technologies EDS-505A Series, Руководство пользователя

Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды