Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-20

When configuring Port Trunking, note that:

Each EDS-505A can set a maximum of 2 Port Trunking groups (designated Trk1, Trk2). Each
EDS-508A can set a maximum of 4 Port Trunking groups (designated Trk1, Trk2, Trk3, Trk4)

When you activate Port Trunking settings, some advanced functions that you setup with the
original ports will either be set to factory default values, or disabled:



Communication Redundancy will be set to the factory default



Traffic Prioritization will be set to the factory default



Port-based VLAN or 802.1Q VLAN will be set to the factory default



Multicast Filtering will be set to the factory default



Rate Limiting will be set to the factory default



Port Access Control will be set to the factory default



Email and Relay Warning will be set to the factory default



Set Device IP will be set to the factory default



Mirror Port will be set to the factory default

You can setup these features again on your Trunking Port.

Configuring Port Trunking

The

Port Trunking Settings

page is used to assign ports to a Trunk Group.

Step 1:

Select Trk1, Trk2, Trk3, or Trk4 from the

Trunk Group

drop-down box.

Step 2:

Select Static, or LACP from the

Trunk Type

drop-down box.

Step 3:

Under

Member Ports

and

Available Ports

, select the specific ports.

Step 4:

Use

the

Up

/

Down

buttons to add/remove designated ports to/from a trunk group.

«
...
33
34
35
36
37
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 2

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 28

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 2

OfficeConnect 1600

Бренд: 3Com Страницы: 8

Бренд: 3Com Страницы: 8

Бренд: Hama Страницы: 10

Бренд: National Instruments Страницы: 26

Бренд: National Instruments Страницы: 85

Module SCXI-1503

Бренд: National Instruments Страницы: 79

Бренд: Lanner Страницы: 2

ThunderLAN TNETE100A

Бренд: Texas Instruments Страницы: 179

Бренд: Ruckus Wireless Страницы: 56

Бренд: Renesas Страницы: 6

Бренд: N.A.T. Страницы: 32

Бренд: IBASE Technology Страницы: 71

Бренд: Net to Net Technologies Страницы: 4

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды