Mitsubishi Fuso CANTER FE85DE6SLGP Скачать руководство пользователя

Страница: 77 / 336

11-39

Inspection procedure

Inspection: Head idler shaft-to-head idler gear bushing
clearance

•

Replace the bushing if the measurement exceeds the specified
limit.

Replacement of head idler gear bushing
[Removal]

[Installation]
•

Position the bushing on the head idler gear with their ends fac-
ing the illustrated directions and their oil holes on the same line.

•

Using

, press the bushing into the head idler gear until it is

flush with the lower edge of the chamfer on the head idler gear.

•

Remeasure the clearance between the bushing and head idler
shaft.

•

Ream the bushing if the measurement is less than the standard
value.

Installation procedure

Installation: Cylinder head

CAUTION

• Before fitting the cylinder head bolts, check the punch

marks on each bolt’s head. Do not use the bolt if there are
three punch marks.

• The punch marks indicate the number of times each bolt

has been tightened using the torque-turn tightening meth-
od. Any bolt that already has three punch marks must be re-
placed.

Содержание Fuso CANTER FE85DE6SLGP

















































































































































































































































































































































Результаты поиска

Содержание Fuso CANTER FE85DE6SLGP

Отзывы:

Похожие инструкции для Fuso CANTER FE85DE6SLGP

Бренды по названию

Популярные бренды

Mitsubishi Fuso CANTER FE85DE6SLGP, Руководство по ремонту

Результаты поиска

Содержание Fuso CANTER FE85DE6SLGP

Отзывы:

Похожие инструкции для Fuso CANTER FE85DE6SLGP

Бренды по названию

Популярные бренды