Mitsubishi MOTORS SHOGUN SPORT, Руководство пользователя

Страница: 225 / 501

Super select 4WD II*
6-58 Starting and driving
6
NOTE
 When the drive mode-selector is set between
“2H”, “4H” and “4HLc”, the front wheel
and/or centre differential lock displays blink
while the selection is in process. Take the
following precautions when the indicator
display is blinking.
• Keep the steering wheel in the straight
ahead position while making range selec-
tions. If you attempt to drive forward with
the steering wheel turned, gear rattling or
shock may occur and the desired range may
not actually be selected.
• When the drive mode-selector is set
between “2H”, “4H” and “4HLc”, while the
vehicle is stopped, the front wheel and/or
centre differential lock displays blink while
the selection is in process. Drive slowly and
normally after confirming that the display
is switched.
• If the front wheel and/or centre differential
lock displays blinking after a “2H”

“4H”

“4HLc” selection has been made with
the vehicle moving, hold the steering wheel
in the straight ahead position and slowly
depress the accelerator pedal several times.
 The front and the rear wheel displays will
blink during shifting process from “4HLc” to
“4LLc” or vice versa, as the transfer passes
through the neutral position. Be sure to oper-
ate the drive mode-selector until the front
and the rear wheel displays illuminate again.
 When parking, apply the parking brake
before stopping the engine and make sure
that the front and the rear wheel displays and
the low range indicator display are not blink-
ing during shifting process between “4HLc”

“4LLc”. Otherwise, the vehicle could
unexpectedly move even if the A/T is in the
“P” (PARK) position.

If, after a “4HLc”

“4LLc” selection has
been made, front and the rear wheel lamps
continue blinking and the desired range is
not actually selected, return the drive mode-
selector to its previous position. Place the
steering wheel in the straight ahead position,
drive the vehicle forward, and release the
accelerator pedal. Next, hold down the clutch
pedal (with M/T) or place the selector lever
in the “N” (NEUTRAL) position (with A/T),
depress and hold the brake pedal and make
the range selection again.
 If the low range indicator display blinks
when you attempt to make a “4HLc”

“4LLc” selection, a “4HLc”

“4LLc”
selection cannot be made. Stop the vehicle
and release the accelerator pedal. Next, hold
down the clutch pedal (with M/T) or place
the selector lever in the “N” (NEUTRAL)
position (with A/T), depress and hold the
brake pedal and make the range selection
again.
NOTE
 If the selector lever is shifted from the “N”
(NEUTRAL) position to the other position or
release the brake pedal during shifting pro-
cess between “4HLc

4LLc”, the warning
display will appear and the shifting process
will be stopped (A/T).
 If the clutch pedal is released during shifting
process between “4HLc

4LLc”, the warn-
ing display will appear and the shifting pro-
cess will be stopped (M/T).
 On vehicles with the active stability & trac-
tion control (ASTC), the active stability con-
trol function is suspended while “4LLc” is
selected. indicator lamp is illuminated
while these functions are suspended. It does
not indicate a problem. When “2H” or “4H”
or “4HLc” is selected, this lamp goes out and
function again. Refer to “ASTC indicator
lamp or ASTC OFF indicator lamp” on page
6-84.
NOTE
BK0240501EN.book 58 ページ ２０１６年１１月１０日 木曜日 午前１０時３５分