Mercury 100 FourStroke Скачать руководство пользователя

Страница: 42 / 141

GOOD VENTILATION

Ventilate the passenger area, open side curtains or forward hatches to remove

fumes.
Example of desired air flow through the boat:

21622

POOR VENTILATION

Under certain running and/or wind conditions, permanently enclosed or canvas

enclosed cabins or cockpits with insufficient ventilation may draw in carbon

monoxide. Install one or more carbon monoxide detectors in your boat.
Although the occurrence is rare, on a very calm day, swimmers and

passengers in an open area of a stationary boat that contains, or is near, a

running engine may be exposed to a hazardous level of carbon monoxide.

1. Examples of poor ventilation while the boat is stationary:

a -

Operating the engine when the boat is moored in a confined space

b -

Mooring close to another boat that has its engine operating

2. Examples of poor ventilation while the boat is moving:

a -

Operating the boat with the trim angle of the bow too high

b -

Operating the boat with no forward hatches open (station wagon effect)

21626

21628

GENERAL INFORMATION

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды