Mercury 100 FourStroke Скачать руководство пользователя

Страница: 32 / 141

Do not overpower or overload your boat. Most boats will carry a required

capacity plate indicating the maximum acceptable power and load as

determined by the manufacturer following certain federal guidelines. If in doubt,

contact your dealer or the boat manufacturer.

U.S. COAST GUARD CAP ACITY
MAXIMUM HORSEPOWER XXX

MAXIMUM PERSON
CAPACITY (POUNDS)

XXX

MAXIMUM WEIGHT
CAPACITY

XXX

26777

High‑Speed and High‑Performance Boat Operation

If your outboard is to be used on a high‑speed or high‑performance boat with

which you are unfamiliar, we recommend that you do not operate it at its high

speed capability without first requesting an initial orientation and familiarization

demonstration ride with your dealer or an operator experienced with your boat/

outboard combination. For additional information, obtain a copy of our

‑

Performance Boat Operation

booklet from your dealer, distributor, or

Mercury Marine.

Outboard Remote Control Models

The remote control connected to your outboard must be equipped with a start

in neutral only protection device. This prevents the engine from starting when

the shift is actuated in any position other than neutral.

WARNING

Starting the engine with the drive in gear can cause serious injury or death.

Never operate a boat that does not have a neutral‑safety‑protection device.

58237

GENERAL INFORMATION

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды