Mercury 100 FourStroke Скачать руководство пользователя

Страница: 73 / 141

EMISSION CERTIFICATION LABEL

An emission certification label, showing emission levels and engine

specifications directly related to emissions, is placed on the engine at the time

of manufacture.

a -

Idle speed

b -

Engine horsepower

c -

Piston displacement

d -

Engine power ‑ kilowatts

e -

Date of manufacture

f -

Family number

g -

Regulated emission limit for the engine family

h -

Regulated emission limit for the engine family

i -

Recommended spark plug and gap

j -

Percent of fuel line permeation

OWNER RESPONSIBILITY

The owner/operator is required to have routine engine maintenance performed

to maintain emission levels within prescribed certification standards.
The owner/operator is not to modify the engine in any manner that would alter

the horsepower or allow emission levels to exceed their predetermined factory

specifications.

Inspection and Maintenance Schedule

BEFORE EACH USE

•

Check engine oil level. Refer to

Fuel and Oil

‑

Checking and Adding

Engine Oil

•

Check that lanyard stop switch stops the engine.

SPARK PLUG:

GAP:

EMISSION CONTROL
INFORMATION

THIS ENGINE CONFORMS TO
EMISSION REGULATIONS FOR SPARK IGNITION MARINE ENGINES

CALIFORNIA AND U.S. EPA

REFER TO OWNERS MANUAL FOR REQUIRED MAINTENANCE,
SPECIFICATIONS, AND ADJUSTMENTS

IDLE SPEED (in gear):

FAMILY:
HC+NOx:FEL:

LOW PERM/HIGH PERM:

g/kWh

HC+NOx:FEL:

g/kWh

CO FEL:

g/kWh

43210

MAINTENANCE

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды