Mercury 100 FourStroke Скачать руководство пользователя

Страница: 113 / 141

FUEL SUPPLY MODULE PRIMING PROCEDURE

The fuel supply module (FSM) is not vented to the ambient air. The air trapped

in the FSM, fuel lines, and fuel rail, will be slightly compressed during the initial

ignition key on with a dry or drained fuel system. Additional key on events

under these conditions, will not compress the air further to finish the priming of

the FSM. Excessive number of key on events may eventually damage the fuel

pumps. The volume of air trapped in the FSM must be purged to prime the fuel

system. This can be achieved by connecting a tool to the fuel rail Schrader

valve fitting to quickly purge the system into an approved container, or by

cranking the engine.

Priming the FSM with a Fuel Pressure Gauge

The use of a purge tool for priming the FSM is the preferred method, but is not

always practical. The objective is to purge the air entrained in the fuel system

through a purge tool connected to the fuel rail Schrader valve test port. During

the key on, opening the dump valve will allow the air to be purged from the

FSM and fuel rail. This method should be used on vessels where the fuel inlet

system to the outboard is restrictive; contains an anti‑siphon valve or holds a

relatively large volume of fuel because of a long fuel supply line or water

separating fuel filter. If a primer bulb is installed, it can be used during the

priming event to shorten the amount of time required to start the engine.

1. Verify the engine is in a level vertical position.
2. Verify the vessel fuel supply line is connected to the outboard fuel system

inlet fitting.

3. Connect a fuel pressure gauge to the fuel rail Schrader valve.

Fuel Pressure Gauge Kit

91‑881833A03

2807

Tests the fuel pump pressure; can be

used to relieve fuel pressure.

OUTBOARD INSTALLATION

eng

103

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды