Mercury 100 FourStroke Скачать руководство пользователя

Страница: 13 / 141

DURATION OF COVERAGE:

This limited corrosion warranty provides

coverage for three (3) years from either the date the product is first sold, or the

date on which the product is first put into service, whichever occurs first. The

repair or replacement of parts, or the performance of service under this

warranty, does not extend the life of this warranty beyond its original expiration

date. Unexpired warranty coverage can be transferred to subsequent

(noncommercial use) purchaser upon proper reregistration of the product.

CONDITIONS THAT MUST BE MET IN ORDER TO OBTAIN WARRANTY
COVERAGE:

Warranty coverage is available only to retail customers that

purchase from a Dealer authorized by Mercury Marine to distribute the product

in the country in which the sale occurred, and then only after the Mercury

Marine specified predelivery inspection process is completed and documented.

Warranty coverage becomes available upon proper registration of the product

by the authorized dealer. Corrosion prevention devices specified in the

Operation and Maintenance Manual must be in use on the boat, and routine

maintenance outlined in the Operation and Maintenance Manual must be timely

performed (including, without limitation, the replacement of sacrificial anodes,

use of specified lubricants, and touch‑up of nicks and scratches) in order to

maintain warranty coverage. Mercury Marine reserves the right to make

warranty coverage contingent upon proof of proper maintenance.

WHAT MERCURY WILL DO:

Mercury Marine's sole and exclusive obligation

under this warranty is limited to, at our option, repairing a corroded part,

replacing such part or parts with new or Mercury Marine certified

remanufactured parts, or refunding the purchase price of the Mercury Marine

product. Mercury Marine reserves the right to improve or modify products from

time to time without assuming an obligation to modify products previously

manufactured.

HOW TO OBTAIN WARRANTY COVERAGE:

The customer must provide

Mercury Marine with a reasonable opportunity to repair, and reasonable access

to the product for warranty service. Warranty claims shall be made by

delivering the product for inspection to a Mercury Marine dealer authorized to

service the product. If the purchaser cannot deliver the product to such a

dealer, written notice must be given to Mercury Marine. Mercury Marine will

then arrange for the inspection and any covered repair. The purchaser, in that

case, shall pay for all related transportation charges and travel time. If the

service provided is not covered by this warranty, the purchaser shall pay for all

related labor and material, and any other expenses associated with that

service. The purchaser shall not, unless requested by Mercury Marine, ship the

product or parts of the product directly to Mercury Marine. Proof of registered

ownership must be presented to the dealer at the time warranty service is

requested in order to obtain coverage.

WARRANTY INFORMATION

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды