Mercury 100 FourStroke Скачать руководство пользователя

Страница: 110 / 141

3. Do not install wedges or plates between the transom clamp brackets and

the transom (or jack plate). Refer to Figure 4.

Figure 4

a -

Boat transom or jack plate

b -

Transom clamp bracket

c -

Wedge/plate

Important Information

Rigging boats, which includes proper engine installation has become more

complex over the years. As a result, Mercury Marine recommends that engines

be installed only by Mercury authorized dealers. If you intend to disregard this

recommendation, and install the engine yourself, please make sure to read and

comply with these instructions. Failure to comply with these installation

instructions could lead to serious injury or death.

NOTE: Do not install an accessory electric fuel pump onto the fuel system for

this engine.

Boat Horsepower Capacity

WARNING

Exceeding the boat's maximum horsepower rating can cause serious injury

or death. Overpowering the boat can affect boat control and flotation

characteristics or break the transom. Do not install an engine that exceeds

the boat's maximum power rating.

54058

OUTBOARD INSTALLATION

100

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды