Mercury 100 FourStroke Скачать руководство пользователя | Manualshive

Страница: 51 / 141

background image

Fuel Recommendations

IMPORTANT: Use of improper fuel can damage your engine. Engine
damage resulting from the use of improper fuel is considered misuse of
the engine. Damages caused from the use of improper fuel is not covered
under the limited warranty.

FUEL RATINGS

Mercury Marine engines will operate satisfactorily when using a major brand of

unleaded gasoline meeting the following specifications:

USA and Canada

‑ having a posted pump octane rating of 87 (R+M)/2

minimum. Premium gasoline (92 [R+M]/2 octane) is also acceptable. Do not

use leaded gasoline.

Outside USA and Canada

‑ having a posted pump octane rating of 90 RON

minimum. Premium gasoline (98 RON) is also acceptable. If unleaded gasoline

is not available, use a major brand of leaded gasoline.

USING BUTANOL FUEL BLENDS (USA ONLY)

Butanol fuel blends up to 16 percent that meet Mercury published fuel

requirements, are an acceptable substitute for unleaded gasoline. Contact your

boat manufacturer for specific recommendations on your boat's fuel system

components (fuel tanks, fuel lines, and fittings).

USING REFORMULATED (OXYGENATED) GASOLINES (USA ONLY)

Reformulated gasoline is required in certain areas of the USA. The two types of

oxygenates used in these fuels are alcohol (ethanol) or ether (MTBE or ETBE).

If ethanol is the oxygenate that is used in the gasoline in your area, refer to

Gasolines Containing Alcohol

.

GASOLINES CONTAINING ALCOHOL

If the gasoline in your area contains either methanol (methyl alcohol) or ethanol

(ethyl alcohol), you should be aware of certain adverse effects that can occur.

These adverse effects are more severe with methanol. Increasing the

percentage of alcohol in the fuel can also worsen these adverse effects.
Alcohol in gasoline can absorb moisture from the air, causing the water and the

alcohol to separate from the gasoline in the fuel tank.
The fuel system components on your Mercury Marine engine will withstand up

to 10% alcohol content in the gasoline. We do not know what percentage your

boat's fuel system will withstand. Contact your boat manufacturer for specific

recommendations on the boat's fuel system components (fuel tanks, fuel lines,

and fittings).
Be aware that gasoline containing alcohol may cause increased:

•

Corrosion of metal parts

•

Deterioration of rubber or plastic parts

•

Fuel permeation through rubber fuel lines

•

Starting and operating difficulties

FUEL AND OIL

eng

41

«
...
49
50
51
52
53
...
»

Содержание 100 FourStroke














































































































































Отзывы:

Нет отзывов

Похожие инструкции для 100 FourStroke

SBC81206 Series

Бренд: AXIOMTEK Страницы: 74

Бренд: Balluff Страницы: 62

Бренд: Intel Страницы: 89

Бренд: Gigabyte Страницы: 125

Бренд: MATSONIC Страницы: 76

Бренд: Analog Devices Страницы: 13

Бренд: IBASE Technology Страницы: 60

Бренд: AMD Geode Страницы: 51

Бренд: IWILL Страницы: 48

Бренд: Epcom Страницы: 8

Бренд: Biostar Страницы: 210

Бренд: CAME Страницы: 4

Бренд: ASROCK Страницы: 38

Бренд: Intersil Страницы: 10

Бренд: u-blox Страницы: 24

Бренд: THORLABS Страницы: 22

Бренд: Renesas Страницы: 6

CC85-CC2590EM Series

Бренд: Texas Instruments Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды