Mercury 100 FourStroke Скачать руководство пользователя

Страница: 106 / 141

Mercury Marine Validated Engine Mounting Hardware

IMPORTANT: Mercury Marine provides validated fasteners and installation

instructions, including torque specifications, with all of our outboards so they

can be properly secured to boat transoms. Improper installation of the outboard

can cause performance and reliability issues that can lead to safety concerns.

Follow all of the instructions relating to the outboard installation. DO NOT

mount any other accessory onto the boat with the fasteners provided with the

outboard. For example, do not mount tow sport bars or boarding ladders onto

the boat using the mounting hardware included with the outboard. Installing

other products onto the boat that utilize the outboard mounting hardware will

compromise the ability of that hardware to properly and safely secure the

outboard to the transom.

Outboards that require validated mounting hardware will have the following

decal on the transom clamp.

51965

Accessories Mounted to the Transom Clamp Bracket

Mercury Marine has been made aware that certain aftermarket marine

accessories, such as emergency boarding ladders, shallow water anchors,

transom wedge kits, and tow sport attaching devices, have been mounted to

the boat by use of the same fasteners that secure the outboard to the transom

or jack plate. Using the same fastener to secure both an accessory and the

engine to the boat compromises the ability of the fasteners to maintain the

proper clamp load. A boat with loose engine mounting fasteners creates the

possibility of performance, durability, and safety issues.

OUTBOARD INSTALLATION

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды