Mercury 100 FourStroke Скачать руководство пользователя

Страница: 123 / 141

CHECKING BOAT TRANSOM CONSTRUCTION

IMPORTANT: Determine the strength of the boat transom. The outboard

mounting locknuts and bolts should be able to hold 75 Nm (55 lb‑ft) of torque

without the boat transom yielding or cracking. If the boat transom yields or

cracks under this torque, the construction of the transom may not be adequate.

The boat transom must be strengthened or the load carrying area increased.

a -

Transom yielding under bolt torque

b -

Transom cracking under bolt torque

Use a dial torque wrench to determine transom strength. If the bolt or nut

continues to turn without the torque reading on the dial increasing, it is an

indication that the transom is yielding. The load area can be increased by using

a larger washer or a transom reinforcement plate.

a -

Large transom washer

b -

Transom reinforcement plate

18961

33962

OUTBOARD INSTALLATION

eng

113

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды