Mercury 100 FourStroke Скачать руководство пользователя | Manualshive

Страница: 55 / 141

background image

REMOVING THE FUEL CAP

a -

Fuel cap

b -

Manual vent screw

c -

Tab lock

IMPORTANT: Contents may be under pressure. Rotate the fuel cap 1/4 turn to

relieve pressure before opening.

1. Open the manual vent screw on top of the fuel cap.
2. Turn the fuel cap until it contacts the tab lock.
3. Press down on the tab lock. Rotate the fuel cap 1/4 turn to relieve the

pressure.

4. Press down on the tab lock again and remove the cap.

DIRECTIONS FOR USING THE PRESSURIZED PORTABLE FUEL TANK

1. When installing the fuel tank cap, turn the cap to the right until you hear a

click. This signals that the fuel cap is fully seated. A built‑in device

prevents overtightening.

2. Open the manual vent screw on top of the cap for operation and cap

removal. Close the manual vent screw for transportation.

3. For fuel hoses that have quick disconnects, disconnect the fuel line from

the engine or fuel tank when not in use.

4. Follow

Filling Fuel Tank

instructions for fueling.

Filling Fuel Tank

!

WARNING

Avoid serious injury or death from a gasoline fire or explosion. Use caution

when filling fuel tanks. Always stop the engine and do not smoke or allow

open flames or sparks in the area while filling fuel tanks.

Fill the fuel tanks outdoors away from heat, sparks, and open flames.
Remove the portable fuel tanks from the boat to fill them.
Always stop the engine before filling the tanks.
Do not completely fill the fuel tanks. Leave approximately 10% of the tank

volume unfilled. Fuel will expand in volume as its temperature rises and can

leak under pressure if the tank is completely filled.

a

b

c

46290

FUEL AND OIL

eng

45

«
...
53
54
55
56
57
...
»

Содержание 100 FourStroke














































































































































Отзывы:

Нет отзывов

Похожие инструкции для 100 FourStroke

Бренд: E-peas Страницы: 2

Бренд: u-blox Страницы: 25

A75A-G35 Series

Бренд: MSI Страницы: 72

otometrics HI-PRO 2

Бренд: natus Страницы: 22

Бренд: Quick Страницы: 32

Бренд: JETWAY Страницы: 38

Бренд: NXP Semiconductors Страницы: 12

Z68A-G45 B3 Series

Бренд: MSI Страницы: 138

Бренд: Micronics Страницы: 80

NCP45491PMNGEVB

Бренд: ON Semiconductor Страницы: 9

Бренд: Acer Страницы: 27

Бренд: Acer Страницы: 20

Бренд: Acer Страницы: 16

Бренд: Acer Страницы: 30

Бренд: Acer Страницы: 26

Бренд: Acer Страницы: 109

Altos 1100 Series

Бренд: Acer Страницы: 114

Altos 12000 Series

Бренд: Acer Страницы: 172

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды