Mercury 100 FourStroke Скачать руководство пользователя | Manualshive

Страница: 14 / 141

background image

WHAT IS NOT COVERED:

This limited warranty does not cover electrical

system corrosion; corrosion resulting from damage, corrosion which causes

purely cosmetic damage, abuse, or improper service; corrosion to accessories,

instruments, steering systems; corrosion to factory installed jet drive unit;

damage due to marine growth; product sold with less than a one year limited

Product warranty; replacement parts (parts purchased by customer); products

used in a commercial application. Commercial use is defined as any work or

employment related use of the product, or any use of the product which

generates income, for any part of the warranty period, even if the product is

only occasionally used for such purposes.
Corrosion damage caused by stray electrical currents (onshore power

connections, nearby boats, submerged metal) is not covered by this corrosion

warranty and should be protected against by the use of a corrosion protection

system, such as the Mercury Precision Parts or Quicksilver MerCathode

system and/or Galvanic Isolator. Corrosion damage caused by improper

application of copper base antifouling paints is also not covered by this limited

warranty. If antifouling protection is required, Tri‑Butyl‑Tin‑Adipate (TBTA) base

antifouling paints are recommended on Outboard and MerCruiser boating

applications. In areas where TBTA base paints are prohibited by law, copper

base paints can be used on the hull and transom. Do not apply paint to the

Outboard or MerCruiser product. In addition, care must be taken to avoid an

electrical interconnection between the warranted product and the paint. For

MerCruiser product, an unpainted gap of at least 38 mm (1.5 in.) should be left

around the transom assembly. Refer to the Operation and Maintenance Manual

for additional details.
For additional information regarding events and circumstances covered by this

warranty, and those that are not, see the Warranty Coverage section of the

Operation and Maintenance Manual, incorporated by reference into this

warranty.

DISCLAIMERS AND LIMITATIONS:

THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A  PARTICULAR  PURPOSE  ARE  EXPRESSLY  DISCLAIMED.  TO  THE
EXTENT  THAT  THEY  CANNOT  BE  DISCLAIMED,  THE  IMPLIED
WARRANTIES  ARE  LIMITED  IN  DURATION  TO  THE  LIFE  OF  THE
EXPRESS WARRANTY. INCIDENTAL AND CONSEQUENTIAL DAMAGES
ARE  EXCLUDED  FROM  COVERAGE  UNDER  THIS  WARRANTY.  SOME
STATES/COUNTRIES  DO  NOT  ALLOW  FOR  THE  DISCLAIMERS,
LIMITATIONS  AND  EXCLUSIONS  IDENTIFIED  ABOVE,  AS  A  RESULT,
THEY  MAY  NOT  APPLY  TO  YOU.  THIS  WARRANTY  GIVES  YOU
SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER LEGAL
RIGHTS  WHICH  VARY  FROM  STATE  TO  STATE  AND  COUNTRY  TO
COUNTRY.

WARRANTY INFORMATION

4

eng

«
...
12
13
14
15
16
...
»

Содержание 100 FourStroke














































































































































Отзывы:

Нет отзывов

Похожие инструкции для 100 FourStroke

Бренд: Yamaha Страницы: 87

NF796M-H310 Series

Бренд: JETWAY Страницы: 63

Бренд: MPS Страницы: 6

Бренд: TYAN Страницы: 67

Бренд: Gigabyte Страницы: 58

cpuModules CME34BT

Бренд: rtd Страницы: 110

Бренд: Nematron Страницы: 47

Бренд: ISSC Страницы: 39

Бренд: Supero Страницы: 77

Бренд: Supermicro Страницы: 147

Бренд: Gigabyte Страницы: 87

AN-1966 LMH2190

Бренд: Texas Instruments Страницы: 11

Бренд: Biostar Страницы: 68

Бренд: Gigabyte Страницы: 34

CC85-CC2590EM Series

Бренд: Texas Instruments Страницы: 7

Бренд: Microchip Technology Страницы: 54

Бренд: JETWAY Страницы: 47

Бренд: Gigabyte Страницы: 75

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды