Mercury 100 FourStroke Скачать руководство пользователя

Страница: 9 / 141

Maintenance

Outboard Care.................................................................................................. 62

EPA Emissions Regulations............................................................................. 62

Inspection and Maintenance Schedule............................................................. 63

Maintenance Schedule Decal (75–115)............................................................ 66

Flushing the Cooling System............................................................................ 67

Top Cowl Removal and Installation.................................................................. 68

Cleaning Care for Top and Bottom Cowls........................................................ 69

Flywheel Cover Removal and Installation.........................................................70

Cleaning Care for the Powerhead (Saltwater Use)...........................................70

Battery Inspection ............................................................................................ 71

Fuel System...................................................................................................... 71

Corrosion Control Anode.................................................................................. 73

Propeller Replacement..................................................................................... 74

Spark Plug Inspection and Replacement..........................................................77

Fuse Replacement............................................................................................79

Lubrication Points............................................................................................. 80

Checking Power Trim Fluid...............................................................................83

Changing Engine Oil ........................................................................................ 83

Gearcase Lubrication........................................................................................86

Storage

Storage Preparation..........................................................................................88

Protecting External Outboard Components...................................................... 88

Protecting Internal Engine Components........................................................... 89

Gearcase.......................................................................................................... 89

Positioning Outboard for Storage..................................................................... 89

Battery Storage................................................................................................. 89

Troubleshooting

Starter Motor Will Not Crank the Engine...........................................................90

Engine Will Not Start.........................................................................................90

Engine Runs Erratically.................................................................................... 90

Performance Loss.............................................................................................91

Battery Will Not Hold Charge............................................................................ 91

eng

vii

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды