Mercury 100 FourStroke Скачать руководство пользователя

Страница: 39 / 141

Any unexpected, sudden reduction in boat speed could result in the elevated

passenger falling over the front of the boat.

26783

Wave and Wake Jumping

Operating recreational boats over waves and wake is a natural part of boating.

However, when this activity is done with sufficient speed to force the boat hull

partially or completely out of the water, certain hazards arise, particularly when

the boat enters the water.

26784

The primary concern is the boat changing direction while in the midst of the

jump. In such case, the landing may cause the boat to veer violently in a new

direction. Such a sharp change in direction can cause occupants to be thrown

out of their seats, or out of the boat.

WARNING

Wave or wake jumping can cause serious injury or death from occupants

being thrown within or out of the boat. Avoid wave or wake jumping whenever

possible.

There is another less common hazardous result from allowing your boat to

launch off a wave or wake. If the bow of your boat pitches down far enough

while airborne, upon water contact it may penetrate under the water surface

and submarine for an instant. This will bring the boat to a nearly instantaneous

stop and can send the occupants flying forward. The boat may also steer

sharply to one side.

GENERAL INFORMATION

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды