Mercury 100 FourStroke Скачать руководство пользователя | Manualshive

Страница: 43 / 141

background image

Selecting Accessories for Your Outboard

Genuine Mercury Precision or Quicksilver Accessories have been specifically

designed and tested for your outboard. These accessories are available from

Mercury Marine dealers.
IMPORTANT: Check with your dealer before installing accessories. The misuse

of approved accessories or the use of nonapproved accessories can damage

the product.
Some accessories not manufactured or sold by Mercury Marine are not

designed to be safely used with your outboard or outboard operating system.

Read the installation, operation and maintenance manuals for all your selected

accessories.
Refer to

Outboard Installation

‑

Accessories Mounted to the Transom

Clamp Bracket

for important information on mounting accessories to the

transom clamp bracket.

Safe Boating Recommendations

To safely enjoy the waterways, familiarize yourself with local and all other

governmental boating regulations and restrictions and consider the following

suggestions.

Know and obey all nautical rules and laws of the waterways.

•

We recommend that all powerboat operators complete a boating safety

course. In the U.S., the U.S. Coast Guard Auxiliary, the Power Squadron,

the Red Cross, and your state or provincial boating law enforcement

agency provide courses. For more information in the U.S., call the Boat

U.S. Foundation at 1‑800‑336‑BOAT (2628).

Perform safety checks and required maintenance.

•

Follow a regular schedule and ensure that all repairs are properly made.

Check safety equipment onboard.

•

Here are some suggestions of the types of safety equipment to carry

when boating:

Approved fire extinguishers
Signal devices: flashlight, rockets or flares, flag, and whistle or horn
Tools necessary for minor repairs
Anchor and extra anchor line
Manual bilge pump and extra drain plugs
Drinking water
Radio
Paddle or oar
Spare propeller, thrust hubs, and an appropriate wrench

GENERAL INFORMATION

eng

33

«
...
41
42
43
44
45
...
»

Содержание 100 FourStroke














































































































































Отзывы:

Нет отзывов

Похожие инструкции для 100 FourStroke

Бренд: Yamaha Страницы: 232

EZ-USB HX2LP CY4605

Бренд: Cypress Страницы: 2

945GC MICRO 775

Бренд: Biostar Страницы: 49

IMBA-G412ISA-R20

Бренд: IEI Technology Страницы: 164

Бренд: Aaeon Страницы: 97

Бренд: Micrel Страницы: 14

Бренд: AKM Страницы: 30

Бренд: Supero Страницы: 80

LPC1768-Xplorer

Бренд: NGX Technologies Страницы: 25

Бренд: Avalue Technology Страницы: 29

Бренд: Gigabyte Страницы: 96

Бренд: Supermicro Страницы: 127

Бренд: MSI Страницы: 6

Бренд: Evalue Technology Страницы: 91

BOOSTXL-DRV8301

Бренд: Texas Instruments Страницы: 13

Бренд: Gigabyte Страницы: 120

Бренд: MSI Страницы: 180

Бренд: Linear Technology Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды