Mercury 100 FourStroke Скачать руководство пользователя

Страница: 60 / 141

It is important to note that in either of the above scenarios, the horn will only

sound one time. If you key the engine off and restart it, the horn will sound

again, one time, if the fault is still present. For visual display of the specific

engine functions and additional engine data, refer to

SmartCraft Product

information, following.
A few of the noncritical conditions indicated by the intermittent short beeps for

six seconds can be corrected by the operator. These operator correctable

conditions are as follows:

•

Water in the boat mounted water separating fuel filter (optional

accessory). Refer to the instructions supplied with the accessory kit.

•

Cooling system (water pressure or engine temperature) problem. Stop the

engine and check the water intake holes in the lower unit for obstruction.

•

Low engine oil level. Refer to

Fuel and Oil – Checking and Adding

Engine Oil

ENGINE GUARDIAN SYSTEM

The Engine Guardian system monitors the critical sensors on the engine for

any early indications of problems. Engine Guardian is functional whenever your

engine is operating, so you never have to be concerned about whether or not

you are protected. The system will respond to a problem by sounding the

warning horn for six seconds and/or reducing engine power in order to provide

engine protection.
If Engine Guardian has been activated, reduce the engine speed. The problem

will need to be identified and corrected. The system must be reset before the

engine will operate at higher speeds. Moving the throttle lever back to the idle

position will reset the Engine Guardian system. If the Engine Guardian system

has determined the reset has not corrected the problem, Engine Guardian will

remain activated, limiting the throttle. The problem must be identified and

corrected before Engine Guardian will allow the engine to reach a normal

operating RPM.

OVERSPEED REV LIMIT

The overspeed rev limit is set at an RPM greater than the operating range. In

the event that the engine is operated at an RPM greater than or equal to the

overspeed limit, the PCM does not allow the engine to maintain the power

requested by the operator. Refer to

Specifications

to determine this engine’s

RPM limit.
Upon reaching the beginning of the rev limit, Engine Guardian will cut‑out the

ignition to specific cylinders. If the operator does not reduce engine speed,

Engine Guardian will cut‑out the ignition to all the cylinders. There is no audible

warning while Engine Guardian overspeed limit is active.
To reset the Engine Guardian protection:

1. Completely reduce the throttle for three seconds.
2. Engage the throttle. If the engine does not respond, repeat step one.

FEATURES AND CONTROLS

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды