Mercury 100 FourStroke Скачать руководство пользователя

Страница: 78 / 141

3. Remove the cover from the flush connector and thread a water hose into

the flush connector.

47592

4. Turn on the water tap (½ maximum) and let the water flush through the

cooling system for about 15 minutes.

5. When flushing is complete, turn off the water and disconnect the water

hose.

6. Install the cover on the flush connector. Place the flush connector back

into the bottom cowl.

Top Cowl Removal and Installation

REMOVAL

Unlock the top cowl by pulling out on the rear cowl latch. Lift the top cowl off the

engine.

53762

INSTALLATION

1. Lower the top cowl over the engine.

MAINTENANCE

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды