Mercury 100 FourStroke Скачать руководство пользователя

Страница: 140 / 141

Trim In Pin

WARNING

Operating the boat at high speeds with the outboard trimmed too far under

can create excessive bow steer, resulting in the operator losing control of the

boat. Install the trim limit pin in a position that prevents excessive trim under

and operate the boat in a safe manner.

Some boats, particularly some bass boats, are built with a greater than normal

transom angle, which will allow the outboard to be trimmed further in or under.

This greater trim under capability is desirable to improve acceleration, reduce

the angle and time spent in a bow high boat during planing off, and in some

cases, may be necessary to plane off a boat with aft livewells, given the variety

of available propellers and height range of engine installations.
However, once on plane, the engine should be trimmed to a more intermediate

position to avoid a bow‑down planing condition called plowing. Plowing can

cause bow steering or oversteering and inefficiently consumes horsepower.

a -

Tilt pin (not included with engine)

Stainless Steel Tilt Pin

17‑49930A 1

2749

Limits the down trim angle of the power

trim equipped engines, or aids in

determining the trim out angle on

non‑power trim engines.

The owner may decide to limit the trim in. This can be accomplished by

purchasing a stainless steel tilt pin from your dealer and insert it in whatever

adjustment hole in the transom brackets is desired. A nonstainless steel

shipping bolt should not be used in this application other than on a temporary

basis.

2688

OUTBOARD INSTALLATION

130

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды