Mercury 100 FourStroke Скачать руководство пользователя

Страница: 107 / 141

WARNING

Avoid serious injury or death resulting from a loss of boat control. Loose

engine fasteners could cause the transom bracket to fail, resulting in a loss of

the driver's ability to control the boat. Always ensure that the engine

fasteners are tightened to the specified torque.

ACCEPTABLE ACCESSORY MOUNTING TO THE TRANSOM CLAMP

BRACKET

After the engine is mounted to the transom or jack plate in accordance with the

engine installation instructions, it is acceptable to attach an accessory to the

boat by use of the unused bolt holes in the transom clamp bracket as shown in

Figure 1.
The following list provides additional guidelines for mounting accessories to the

transom clamp bracket.

•

The accessory fasteners must pass through the boat transom or jack

plate.

OUTBOARD INSTALLATION

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды