Mercury 100 FourStroke Скачать руководство пользователя

Страница: 80 / 141

Flywheel Cover Removal and Installation

REMOVAL

Lift the cover off the four mounting pins.

a -

Flywheel cover

b -

Four mounting pins, two on each side of the engine

INSTALLATION

Position the cover onto the four mounting pins and secure the cover in place by

pushing the cover down onto the mounting pins.

Cleaning Care for the Powerhead (Saltwater Use)

If the outboard is operated in saltwater, remove the top cowl and flywheel

cover. Inspect the powerhead and powerhead components for salt buildup.

Wash off any salt buildup from the powerhead and powerhead components

with fresh water. Keep water spray out of the air filter/intake and alternator.

After washing, allow the powerhead and components to dry. Apply Quicksilver

or Mercury Precision Lubricants Corrosion Guard spray on the external metal

surfaces of the powerhead and powerhead components. Do not allow the

Corrosion Guard spray to come in contact with the alternator drive belt or belt

pulleys.
IMPORTANT: Do not allow lubricant or Corrosion Guard spray to come in

contact with the alternator drive belt or the belt pulleys. The alternator drive belt

could slip and be damaged if it becomes coated with any lubricant or Corrosion

Guard spray.

53765

MAINTENANCE

eng

Содержание 100 FourStroke














































































































































Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды

Mercury 100 FourStroke, Руководство по эксплуатации, техническому обслуживанию, установке и гарантии

Результаты поиска

Содержание 100 FourStroke

Отзывы:

Похожие инструкции для 100 FourStroke

Бренды по названию

Популярные бренды