Mercury 100 FourStroke Скачать руководство пользователя | Manualshive

Страница: 44 / 141

background image

First aid kit and instructions
Waterproof storage containers
Spare operating equipment, batteries, bulbs, and fuses
Compass and map or chart of the area
Personal flotation device (one per person onboard)

Watch for signs of weather change and avoid foul weather and rough

‑

sea

boating.
Tell someone where you are going and when you expect to return.
Passenger boarding.

•

Stop the engine whenever passengers are boarding, unloading, or are

near the back (stern) of the boat. Shifting the drive unit into neutral is not

sufficient.

Use personal flotation devices.

•

Federal law requires that there be a U.S. Coast Guard‑approved life

jacket (personal flotation device), correctly sized and readily accessible

for every person onboard, plus a throwable cushion or ring. We strongly

advise that everyone wear a life jacket at all times while in the boat.

Prepare other boat operators.

•

Instruct at least one person onboard in the basics of starting and

operating the engine and boat handling in case the driver becomes

disabled or falls overboard.

Do not overload your boat.

•

Most boats are rated and certified for maximum load (weight) capacities

(refer to your boat's capacity plate). Know your boat's operating and

loading limitations. Know if your boat will float if it is full of water. When in

doubt, contact your authorized Mercury Marine dealer or the boat

manufacturer.

Ensure that everyone in the boat is properly seated.

•

Do not allow anyone to sit or ride on any part of the boat that was not

intended for such use. This includes the backs of seats, gunwales,

transom, bow, decks, raised fishing seats, and any rotating fishing seat.

Passengers should not sit or ride anywhere that sudden unexpected

acceleration, sudden stopping, unexpected loss of boat control, or sudden

boat movement could cause a person to be thrown overboard or into the

boat. Ensure that all passengers have a proper seat and are in it before

any boat movement.

Never operate a boat while under the influence of alcohol or drugs. It is
the law.

•

Alcohol or drugs can impair your judgment and greatly reduce your ability

to react quickly.

Know your boating area and avoid hazardous locations.

GENERAL INFORMATION

34

eng

«
...
42
43
44
45
46
...
»

Содержание 100 FourStroke














































































































































Отзывы:

Нет отзывов

Похожие инструкции для 100 FourStroke

Бренд: A-Trend Страницы: 40

Бренд: Giada Страницы: 2

Бренд: SOYO Страницы: 95

Бренд: Gigabyte Страницы: 100

Бренд: DFI Страницы: 8

Бренд: Advantech Страницы: 98

VAR-SOM-MX8M-NANO

Бренд: Variscite Страницы: 2

Бренд: BiPOM Electronics Страницы: 12

Бренд: IEI Technology Страницы: 156

Бренд: Gigabyte Страницы: 18

Бренд: Aaeon Страницы: 108

Бренд: Avalue Technology Страницы: 71

BLKD955XBKLKR - 10PK 955X LGA775 8GB DDR2 16X

Бренд: Intel Страницы: 94

Бренд: ASROCK Страницы: 71

Бренд: Suzuki Страницы: 283

SPC58XXADPT144S REV.B

Бренд: ST Страницы: 19

Бренд: DFI-ITOX Страницы: 137

X299 OC Formula

Бренд: ASROCK Страницы: 250

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды