Maquet SERVO-air Скачать руководство пользователя

Страница: 127 / 171

8.2.2 Logs

LOGS is used for viewing event logs for a

certain period of time. A date interval can also

be set and a search function is available.

To access LOGS:

•

Tap BIOMED/LOGS.

The following search filters are available:

- Alarms

- Functions

- Settings

- Configuration

8.2.3 Service report

SERVICE REPORT is used for reporting

service tasks.

8.2.4 Configuration

CONFIGURATION is used for viewing and

editing the startup configuration settings and

alarms as well as for setting date and time and

the biomed code.

To access CONFIGURATION:

•

Tap BIOMED/CONFIGURATION.

The following configurations can be viewed

and edited:

SETTINGS

STARTUP CONFIGURATION

ALARMS

NETWORK

SET DATE & TIME

BIOMED CODE

Settings

SETTINGS is used for configuring the settings

for exporting information via Remote Services.

To access SETTINGS:

•

Tap BIOMED/CONFIGURATION/SETTINGS.

SERVO-air Ventilator System v2.2, User's Manual

127

Service & Settings

| 8 |

Содержание SERVO-air












































































































































































Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды

Maquet SERVO-air, Руководство пользователя

Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды