Maquet SERVO-air Скачать руководство пользователя

Страница: 129 / 171

Edit Temporary O

increase (%)

To edit the oxygenation concentration:

•

Tap CONFIGURATION/STARTUP

CONFIGURATION/O

% and adjust.

The setting entered in the window that opens

determines the default setting for the O

BOOST LEVEL and the oxygen level increase

during pre- and post-oxygenation when

DISCONNECTION/SUCTION is used.

It does not affect the O

BOOST LEVEL

function in the adult patient category where

the default is 100 %.

Important: The ventilator system must be

restarted to activate the new settings.

Alarms

The alarm settings are the default settings that

the ventilator system is delivered with. These

defaults can be changed.

To access ALARMS:

•

Tap BIOMED/CONFIGURATION/ALARMS.

The following alarm categories can be viewed

and managed depending on the installed

configuration:

Pediatric

Pediatric NIV

Adult

Adult NIV

The following can be adjusted:

Default audio level

Restore default audio level

Restore default alarm limits

Options to restore defaults, cancel or save

changes are available for all alarms.

SERVO-air Ventilator System v2.2, User's Manual

129

Service & Settings

| 8 |

Содержание SERVO-air












































































































































































Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды

Maquet SERVO-air, Руководство пользователя

Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды