Maquet SERVO-air Скачать руководство пользователя

Страница: 113 / 171

7.2 Handling alarms

7.2.1 Alarm indication

The alarms are divided into three priorities:

•

high priority — all alarm indications are red

•

medium priority — all alarm indications are

yellow

•

low priority — all alarm indications are blue

Technical error messages indicating a

technical problem are presented together with

a numeric code, TE: x.

When the alarm log is full, the oldest data is

discarded when new alarms are added.

An alarm message explaining the cause of the

alarm is displayed in the alarm list in the status

bar.

The numerical value for the parameter causing

the alarm flashes with the color of the alarm

priority and the exceeded alarm limit is circled

in the same color.

Alarm sound level

When one or more alarms are activated, the

system will present the audio signal

corresponding to the alarm with the highest

priority that is not silenced or turned off.

The alarm volume can be set in the ALARM

LIMITS window.

Refer to section Set alarm sound level on

page 45.

The set alarm sound level is not maintained,

when changing between invasive and non

invasive ventilation and vice versa.

The default alarm sound level can be set in

SERVICE & SETTINGS/BIOMED/

CONFIGURATION/ALARMS window.

Refer to section Alarms on page 129.

SERVO-air Ventilator System v2.2, User's Manual

113

Alarm handling

| 7 |

Содержание SERVO-air












































































































































































Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды

Maquet SERVO-air, Руководство пользователя

Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды