Maquet SERVO-air Скачать руководство пользователя страница 45

Страница: 45 / 171

To activate the new alarm limits tap Accept.

Note: Autoset all alarms is not available in

supported or NIV modes or in STANDBY

because the ventilator system requires

patient values in order to propose alarm

limits.

3.7.1 Set alarm sound level

The ambient sound needs to be taken into

consideration when setting the alarm sound

level.

•

Tap ALARM LIMITS in the quick menu.

•

Tap alarm sound level.

•

Tap the sound level bar to set appropriate

alarm sound level.

•

Tap Accept.

3.8 Enter patient data

•

Tap the patient data shortcut in the status

bar or tap PATIENT DATA in the quick

menu.

•

Tap in the selected input field to open a

keyboard or keypad.

•

Tap Accept to confirm new data.

•

Enter/edit the following data:

- Patient category

- Name

- Date of birth / ID

- Gender

- Height

- Weight

Note: If gender, height and weight have

been entered, predicted body weight will

be automatically displayed.

Refer to section Predicted body weight

(PBW) on page 93.

•

Tap Done when entry is complete.

SERVO-air Ventilator System v2.2, User's Manual

Operation overview

| 3 |

Содержание SERVO-air












































































































































































Результаты поиска

Содержание SERVO-air

Отзывы:

Maquet SERVO-air, Руководство пользователя, Страница: 45 / 171

Результаты поиска

Содержание SERVO-air

Отзывы: