Maquet SERVO-air Скачать руководство пользователя

Страница: 89 / 171

6.6 Inspiratory rise time

The inspiratory rise time (T

insp.rise

•

is the time taken to reach peak inspiratory

flow or pressure at the start of each breath

•

is expressed in seconds or as a percentage

of the respiratory cycle time depending on

how the ventilator is configured

0.10

An increased inspiratory rise time will affect

the rate of flow/pressure increase and can be

evaluated by the shape of the flow and

pressure waveforms.

In supported modes, the inspiratory rise time

should normally be increased from the default

setting to enhance patient comfort.

Inspiratory rise time set as a percentage is

applicable in:

•

PRVC

•

all SIMV modes

•

all Automode modes

Inspiratory rise time set in seconds is

applicable in:

•

Bi-Vent/APRV

Note: When the ventilator system is

configured for setting of inspiration time

rather than I:E ratio, the unit for inspiratory

rise time automatically switches to seconds

for all ventilation modes.

SERVO-air Ventilator System v2.2, User's Manual

Ventilatory settings and functions

| 6 |

Содержание SERVO-air












































































































































































Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды

Maquet SERVO-air, Руководство пользователя

Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды