Maquet SERVO-air Скачать руководство пользователя страница 128

Страница: 128 / 171

Startup Configuration

To access STARTUP CONFIGURATION:

•

Tap BIOMED/CONFIGURATION/STARTUP

CONFIGURATION.

The following items can be viewed and edited:

Patient category

Ventilation type (invasive or non invasive

(NIV))

Volume setting (Tidal volume, Minute

volume)

NIV disconnection functionality (Low flow,

Disabled or High flow)

Breath cycle setting (I:E, T

)

Extended leakage test (Off, On)

Temporary O

increase (%)

Use 0 (s) as default pause time (Off, On)

Deactivation of backup function (Not

allowed, Allowed)

Edit NIV disconnection function

To edit the NIV disconnection functionality:

•

Tap CONFIGURATION/STARTUP

CONFIGURATION/NIV disconnection

functionality.

•

Choose Low flow, Disabled or High flow.

Refer to section Functions in ventilation modes

on page 149.

128

SERVO-air Ventilator System v2.2, User's Manual

| 8 |

Service & Settings

Содержание SERVO-air












































































































































































Результаты поиска

Содержание SERVO-air

Отзывы:

Maquet SERVO-air, Руководство пользователя, Страница: 128 / 171

Результаты поиска

Содержание SERVO-air

Отзывы: