Maquet SERVO-air Скачать руководство пользователя

Страница: 102 / 171

6.15.3 Deactivating backup ventilation

It is possible to deactivate backup ventilation

for invasive PS/CPAP and VS. If backup

ventilation is deactivated, the No patient effort

alarm will be activated at the end of the apnea

time but no backup ventilation will start.

To allow deactivation of backup ventilation:

•

Tap SERVICE & SETTINGS in the extended

menu in STANDBY.

•

Tap BIOMED and enter the code, then tap

CONFIGURATION/STARTUP

CONFIGURATION/Deactivation of backup

function.

•

Change from Not allowed to Allowed.

If this choice is made, Deactivate backup

ventilation is displayed at the top right of the

mode settings window during ventilation.

To deactivate backup ventilation:

•

Tap Deactivate backup ventilation in the

mode settings window.

•

A confirmation dialog Do you really want to

deactivate backup ventilation? is displayed.

Confirm by pressing Yes.

•

Tap Accept in the mode settings window.

•

Backup ventilation off is displayed after the

mode name in the heading when ventilation

then begins.

The backup function is automatically

re-activated if:

•

a change is made to a controlled mode of

ventilation

•

the ventilator system is switched to Standby

•

the system is turned off.

Note: Backup ventilation remains inactive

if a change of mode is made between

PS/CPAP and VS.

102

SERVO-air Ventilator System v2.2, User's Manual

| 6 |

Ventilatory settings and functions

Содержание SERVO-air












































































































































































Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды

Maquet SERVO-air, Руководство пользователя

Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды