Maquet SERVO-air Скачать руководство пользователя

Страница: 106 / 171

Adding medication

Note: Do not use a syringe with a needle

to add medication.

•

Open the filler cap plug on the nebulizer

unit.

•

Use a pre-filled ampoule or syringe to add

medication into the filler port of the

nebulizer unit.

•

Close the filler cap plug.

Note: Medication can also be added in this

manner during nebulization. This does not

interrupt nebulization or ventilation.

Nebulization

Nebulization can be either:

•

switched on/off for a certain period of time

•

continuous, only Aerogen Solo

Nebulization On/Off

To operate the nebulizer for a specific period

of time (on/off):

Tap MANEUVERS/NEBULIZATION.

Tap Time if more or less than 10 minutes

is required and adjust the figure up or

down.

If the nebulizer cable is not connected, a

dialog Check nebulizer cable connection is

displayed on the screen. Tap OK to accept.

Tap START NEBULIZATION PERIOD. The

default is 10 minutes.

Check that nebulization is in progress and

how much time remains by looking at the

progress symbol.

106

SERVO-air Ventilator System v2.2, User's Manual

| 6 |

Ventilatory settings and functions

Содержание SERVO-air












































































































































































Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды

Maquet SERVO-air, Руководство пользователя

Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды