Maquet SERVO-air Скачать руководство пользователя

Страница: 25 / 171

2.3.3 Battery status

Important:

•

If Replace battery is displayed, the

battery is unreliable, regardless of the

operating time displayed under Batteries.

In this situation, replace the battery even

when the STATUS window indicates that

significant operating time remains.

•

At least one battery module must always

be installed.

Detailed information about batteries is

accessed via SYSTEM STATUS/Batteries.

There is also an indication in the status bar

showing the power supply currently being

used by the ventilator system.

If the ventilator system is running on battery

power, the active battery in the battery symbol

turns yellow and the mains power symbol

disappears. The estimated remaining battery

time in minutes is always displayed, regardless

of the power supply in use.

The battery symbol also functions as a

shortcut to the window otherwise accessed

via SYSTEM STATUS/Batteries.

The following information is displayed under

Batteries in SYSTEM STATUS for each

connected battery module:

•

BATTERY CAPACITY – usable backup time

in minutes

An estimated backup time is shown in

Standby. This estimate may differ from the

actual usable backup time during running.

Usable backup time depends on set mode

and selected ventilation settings.

Note: The presented usable backup time

is the sum of the estimated operation

time displayed for each battery module

minus 20 minutes.

•

Slot number

•

Serial number

•

Remaining operation time in minutes for

each battery

•

Notification – may be displayed close to the

remaining operation time in minutes.

•

Remaining battery life

SERVO-air Ventilator System v2.2, User's Manual

System Overview

| 2 |

Содержание SERVO-air












































































































































































Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды

Maquet SERVO-air, Руководство пользователя

Результаты поиска

Содержание SERVO-air

Отзывы:

Похожие инструкции для SERVO-air

Бренды по названию

Популярные бренды