Intel 8XC196NT Скачать руководство пользователя страница 390 | Manualshive

Страница: 390 / 597

Intel 8XC196NT Скачать руководство пользователя страница 390

15-27

PROGRAMMING THE NONVOLATILE MEMORY

15.9.2 Operating Environment

In the auto programming mode, the PCCBs are loaded into the chip configuration registers. Since
the device gets programming data through the external bus, the memory device in the program-
ming system must correspond to the default configuration (Figure 15-6 on page 15-18). Auto pro-
gramming requires an 8-bit bus configuration, so the circuit must tie the BUSWIDTH pin low.
The PCCB defaults allow you to use any standard EPROM that satisfies the AC specifications
listed in the device datasheet.

The auto programming mode also loads CCB0 into an internal RAM location and checks the lock
bits. If either lock bit is programmed, the auto programming routine compares the internal secu-
rity key to the external security key location. If the verification fails, the device enters an endless
internal loop. If the security keys match, the routine continues. The auto programming routine
uses the modified quick-pulse algorithm and the pulse width value programmed into the external
EPROM (locations 14H and 15H).

15.9.3 Auto Programming Routine

Figure 15-13 illustrates the auto programming routine. This routine checks the security lock bits
in CCB0; if either bit is programmed, it compares the internal security key to the external security
key locations. If the security keys match, the routine continues; otherwise, the device enters an
endless loop.

Table 15-10. Auto Programming Memory Map

Address

Output from

8XC196

Device

(A15:0)

Internal

OTPROM

Address

Address

Using Circuit

in Figure

15-12

(P1.2:1, A13:0)

Description

4014H

N/A

14H

Programming pulse width (PPW) LSB.

4015H

N/A

15H

Programming pulse width (PPW) MSB.

4020–402FH

FF2020–FF202FH

0020–002FH

Security key for verification.

4000–7FFFH

FF2000–FF9FFFH

4000–BFFFH

Code, data, and reserved locations.

«
...
388
389
390
391
392
...
»

Содержание 8XC196NT






















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды