manualshive.com logo in svg

Intel 8XC196NT, Руководство пользователя

Поделиться
Скачать
Intel 8XC196NT Скачать руководство пользователя страница 207

8XC196NT USER’S MANUAL

8-12

3

STE

Single Transfer Enable

Enables and disables transfer of a single byte. Unless ATR is set, STE is 
automatically cleared at the end of a transfer. The THS, STE, and ATR 
bits must be set for handshaking modes.

0 = disable transfers
1 = allow transmission or reception of a single byte

2

ATR

Automatic Transfer Re-enable

Enables and disables subsequent transfers. The THS, STE, and ATR bits 
must be set for handshaking modes.

0 = allow automatic clearing of STE; disable subsequent transfers
1 = prevent automatic clearing of STE; allow transfer of next byte

1

OUF

Overflow/Underflow Flag

Indicates whether an overflow or underflow has occurred. An attempt to 
access SSIO

x

_BUF during a byte transfer sets this bit.

For the master (M/S# = 1)

0 = no overflow or underflow has occurred
1 = the core attempted to access SSIO

x

_BUF during the current transfer

For the slave (M/S# = 0)

0 = no overflow or underflow has occurred
1 = the core attempted to access SSIO

x

_BUF during the current transfer

or the master attempted to clock data into or out of the slave’s 
SSIO

x

_BUF before the buffer was available

0

TBS

Transceiver Buffer Status

Indicates the status of the channel’s SSIO

x

_BUF.

For the transmitter (T/R# =1)

0 =  SSIO

x

_BUF is full; waiting to transmit

1 = SSIO

x

_BUF is empty; buffer available

For the receiver (T/R# = 0)

0 = SSIO

x

_BUF is empty; waiting to receive

1 = SSIO

x

_BUF is full; data available

SSIO

x

_CON (Continued)

x

 = 0–1

Address:

1FB1H, 1FB3H

Reset State:

00H

The synchronous serial control 

x

 (SSIO

x

_CON) registers control the communications mode and 

handshaking. The two least-significant bits indicate whether an overflow or underflow has occurred 
and whether the channel is ready to transmit or receive.

7

0

M/S#

T/R#

TRT

THS

STE

ATR

OUF

TBS

Bit 

Number

Bit 

Mnemonic

Function

†

 The M/S# and T/R# bits specify four possible configurations: master transmitter, master receiver, 

slave transmitter, or slave receiver.

Figure 8-6.  Synchronous Serial Control 

x (SSIOx_CON) Registers (Continued)

           

Содержание 8XC196NT






















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды