Intel 8XC196NT Скачать руководство пользователя страница 217 | Manualshive

Страница: 217 / 597

Intel 8XC196NT Скачать руководство пользователя страница 217

8XC196NT USER’S MANUAL

9-4

Table 9-1. Slave Port Signals

Port Pin

Slave

Port

Signal

Slave Port

Signal Type

Description

P3.7:0

SLP7:0

I/O

Slave Port Address/Data bus

Slave port address/data bus in multiplexed mode and slave port
data bus in demultiplexed mode. In multiplexed mode, SLP1 is
the source of the internal control signal, SLP_ADDR.

P5.0

SLPALE

I

Slave Port Address Latch Enable

Functions as either a latch enable input to latch the value on
SLP1 (with a multiplexed address/data bus) or as the source of
the internal control signal, SLP_ADDR (with a demultiplexed
address/data bus).

P5.1

SLPCS#

I

Slave Port Chip Select

SLPCS# must be held low to enable slave port operation.

P5.2

SLPWR#

I

Slave Port Write Control Input

This active-low signal is an input to the slave. The rising edge of
SLPWR# latches data on port 3 into the P3_PIN or SLP_CMD
register.

SLPWR# is multiplexed with P5.2, WR#, and WRL#.

P5.3

SLPRD#

I

Slave Port Read Control Input

This active-low signal is an input to the slave. Data from the
P3_REG or SLP_STAT register is valid after the falling edge of
SLPRD#.

P5.4

SLPINT

O

Slave Port Interrupt

This active-high slave port output signal can be used to interrupt
the master processor.

NOTE:

SLPINT is multiplexed with P5.4 and a special test-
mode-entry pin . Because driving this pin low on the ris-
ing edge of RESET# could cause the device to enter a
reserved test mode, this pin should not be used as an
input.

Table 9-2. Slave Port Control and Status Registers

Mnemonic

Address

Description

INT_MASK

0008H

Interrupt Mask

Setting bit 6 enables the output buffer empty (OBE) interrupt; clearing
the bit disables it.

Setting bit 7 enables the input buffer full (IBF) interrupt; clearing the bit
disables it.

INT_MASK1

0013H

Interrupt Mask 1

Setting bit 0 enables the command buffer full (CBF) interrupt; clearing
the bit disables it.

INT_PEND

0009H

Interrupt Pending

Bit 6, when set, indicates a pending output buffer empty (OBE) interrupt.
This bit is set after the master writes to the data input register, P3_PIN.

Bit 7, when set, indicates a pending input buffer full (IBF). This bit is set
after the master reads from the data output register, P3_REG.

«
...
215
216
217
218
219
...
»

Содержание 8XC196NT






















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды