Integra DTR-70.2, Инструкция по эксплуатации

Страница: 55 / 124

55
En
■
Front
`
Full Band
`
40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz(THX) ,
90Hz , 100Hz , 110Hz , 120Hz , 130Hz , 150Hz , 200Hz
Note
• If the “ Subwoofer ” setting is set to “ No ”, the “ Front ” setting is
fixed at “ Full Band ”.
■
Center *1 , Surround *1*2 , Surround Back *3*4*5*8
`
Full Band
`
40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz(THX) ,
90Hz , 100Hz , 110Hz , 120Hz , 130Hz , 150Hz , 200Hz
`
None :
Select if no speaker is connected.
■
Front Wide *1*3*7*9 , Front High *1*3*6*9
`
Full Band
`
40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz(THX) ,
90Hz , 100Hz , 110Hz , 120Hz , 130Hz , 150Hz , 200Hz
`
None :
Select if no speaker is connected.
Note
*1
“ Full Band ” can be selected only when “ Full Band ” is
selected in the “ Front ” setting.
*2
If the “ Powered Zone 4 ” setting is set to “ Act ” (
➔
86 ), this
setting cannot be selected.
*3
If the “ Surround ” setting is set to “ None ”, this setting cannot
be selected.
*4
If the “ Surround ” setting is set to anything other than “ Full
Band ”, “ Full Band ” cannot be selected here.
*5 If the “ Powered Zone 3 ” setting is set to “ Act ” (
➔
86 ), or
“ Bi-Amp ” or “ BTL ” is being used (
➔
54 ), this setting cannot
be selected.
*6
If the Powered Zone 2 is being used (
➔
86 ), this setting can-
not be selected.
*7
If the “ Powered Zone 2 ” setting is set to “ Act ” (
➔
86
), this
setting cannot be selected.
*8
This setting cannot be used if the “ Front High + Front
Wide ” setting is set to “ Yes ”.
*9 If the “ Passive Subwoofer ” setting is set to “ Use ” (
➔
54 ),
this setting cannot be selected.
■
Surround Back Ch
`
1ch :
Select if only one surround back speaker is con-
nected.
`
2ch :
Select if two (left and right) surround back speakers
are connected.
Note
• If the “ Surround Back ” setting is set to “ None ”, this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
`
80Hz , 90Hz , 100Hz , 110Hz , 120Hz
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
■
Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left, right, and
center channels to the subwoofer.
`
On :
Double Bass function on.
`
Off(THX) :
Double Bass function off.
Note
• This function can be set only if the “ Subwoofer ” setting is set to
“ 1ch ” or “ 2ch ”, and the “ Front ” setting is set to “ Full Band ”.
• If you’re using THX-certified speakers, select “ Off(THX) ”.
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer
intended.
■
Unit
`
feet :
Distances can be set in feet. Range: “ 0.2ft ” to
“ 30.0ft ” in 0.2 foot steps.
`
meters :
Distances can be set in meters. Range: “ 0.06m ” to
“ 9.00m ” in 0.06 meter steps.
(The default setting varies from country to country.)
■
Left, Front Wide Left, Front High Left, Center,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right,
Surround Back Left, Surround Left,
Subwoofer 1, Subwoofer 2
*1
`
Specify the distance from the each speaker to your lis-
tening position.
Note
• Speakers that you set to “ No ” or “ None ” in the
“ Speaker Configuration ” cannot be selected (
➔
54
).
*1 If the “ Subwoofer ” setting is set to “ 1ch ”, this setting cannot
be selected (
➔
54 ).
This setting is NOT set automatically by
Audyssey MultEQ
® XT32 Room Correction and
Speaker Setup function (
➔
29 ).
This setting is set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function (
➔
29 ).