Integra DTR-70.2, Инструкция по эксплуатации

Страница: 51 / 124

51
En
■
Resolution
You can specify the output resolution for the HDMI
output
and COMPONENT VIDEO MONITOR OUT and have
the AV receiver upconvert the picture resolution as neces-
sary to match the resolution supported by your TV.
`
Through *1 :
Select this to pass video through the AV receiver at
the same resolution and with no conversion.
`
Auto *2 :
Select this to have the AV receiver automatically
convert video at resolutions not supported by your
TV.
`
480p ( 480p/576p ):
Select this for 480p or 576p output and video con-
version as necessary.
`
720p :
Select this for 720p output and video conversion as
necessary.
`
1080i :
Select this for 1080i output and video conversion as
necessary.
`
1080p
*2
:
Select this for 1080p output and video conversion as
necessary.
`
1080p/24 *2 :
Select this for 1080p output at 24 frames per second
and video conversion as necessary.
`
Source :
Output will be according to the resolution level
which was set in the “
Picture Adjust ” setting
(
➔
63 ).
Tip
• The “ Resolution ” setting is set respectively of main, sub, and
analog.
• You can see the picture by pressing Enter to check the “ Resolu-
tion ” setting (excluding NET/USB input source).
Note
• If the “ Monitor Out ” setting is set to “ Both ”, this setting is fixed
at “ Auto ”.
• Depending on the incoming video signal, video playback may
not be smooth or the vertical resolution may be lowered. In this
case select other than “
1080p/24 ”.
*1
PC IN (Analog RGB) input signal is output at 480p
(480p/576p), 720p, 1080i resolution when the “
Monitor Out ”
setting is set to “ Analog ” (
➔
50 ) and the “ Resolution ” set-
ting is set to “ Through ”.
*2 These settings are not available when the “ Monitor Out ” set-
ting is set to “ Analog ” (
➔
50
).
HDMI Input
If you connect a video component to an HDMI input, you
must assign that input to an input selector. For example, if
you connect your Blu-ray Disc/DVD player to
HDMI
IN 2 , you must assign “ HDMI 2 ” to the “ BD/DVD ” input
selector.
If you’ve connected your TV to the AV receiver with an
HDMI cable, composite video, S-video and component
video sources can be upconverted
* and output by the
HDMI output *1 . You can set this for each input selector by
selecting the “ - - - - - ” option.
*1
This applies only when “ Monitor Out ” setting is set to other
than “ Analog ” (
➔
50 ).
Here are the default assignments.
■
BD/DVD , VCR/DVR , CBL/SAT , GAME , PC , TAPE ,
TV/CD , PHONO , PORT
`
HDMI 1 , HDMI 2 , HDMI 3 , HDMI 4 , HDMI 5 ,
HDMI 6 , HDMI 7 :
Select the
HDMI IN
to which the video component
has been connected.
`
- - - - - :
Output composite video, S-Video, and component
video sources from the HDMI output. The video out-
put signal from the HDMI output is the one config-
ured in “Component Video Input” (
➔
52 ).
• “ AUX ” is used only for input from the front panel.
• Each HDMI input cannot be assigned to two input selec-
tors or more. When HDMI 1 - HDMI 7 have already
been assigned, you must set first any unused input selec-
tors to “
- - - - - ” or you will be unable to assign HDMI 1
- HDMI 7 to input selector.
Input selector Default assignment
BD/DVD HDMI 1
VCR/DVR HDMI 2
CBL/SAT HDMI 3
GAME HDMI 4
PC HDMI 5
AUX FRONT (Fixed)
TAPE - - - - -
TUNER - - - - - (Fixed)
TV/CD - - - - -
PHONO - - - - -
PORT - - - - -
IN
OUT
Composite video, S-Video,
component video
Composite video, S-Video,
component video
HDMI
HDMI