Integra DTR-70.2, Инструкция по эксплуатации

Страница: 56 / 124

56
En
Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
■
Left, Front Wide Left, Front High Left, Center *1 ,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right,
Surround Back Left, Surround Left
`
–12.0dB to 0.0dB to +12.0dB in 0.5 dB step.
■
Subwoofer 1 *1 , Subwoofer 2 *1*2
`
–15.0dB to 0.0dB to +12.0dB in 0.5 dB step.
Note
• Speakers that you set to “ No ” or “ None ” in the
“ Speaker Configuration ” cannot be selected (
➔
54 ).
• The speakers cannot be calibrated while the AV receiver is
muted.
• The test tone is output at the standard level for THX, which is
0 dB (absolute volume setting 82). If you normally listen at vol-
ume settings below this, be careful because the test tone will be
much louder.
• The “ Level Calibration ” setting cannot be selected if “ Audio
TV Out ” setting is set to “ On ”.
*1 For the center speaker and subwoofer, the level settings made
by using the Home menu are saved (
➔
27
).
*2 If the “ Subwoofer ” setting is set to “ 1ch ”, this setting cannot
be selected (
➔
54 ).
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
Equalizer Settings
With the Equalizer settings, you can adjust the tone of
speakers individually with a 15-band equalizer. The vol-
ume of each speaker can be set (
➔
56 ).
■
Equalizer
`
Manual :
You can adjust the equalizer for each speaker manu-
ally. If you selected “
Manual ”, continue with this
procedure.
`
Audyssey :
This is selected automatically by
Audyssey MultEQ XT32 Room Correction and
Speaker Setup function. The
Audyssey indicator will
light (
➔
9 ) and “ Dynamic EQ ” and
“ Dynamic Volume ” become available (
➔
60 ).
When “ Audyssey ” is selected, “ Dolby Volume ”
becomes “ Off ” automatically (
➔
58 ).
`
Off :
Tone off, response flat.
This setting is set automatically by
Audyssey MultEQ
® XT32 Room Correction and
Speaker Setup function (
➔
29 ).
This setting is set automatically by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function (
➔
29 ).
1
Press
w
to select “Channel”, and then use
e / r to select a speaker.
2
Use
q
/
w
to select a frequency, and then use
the
e
/
r
to adjust the level at that frequency.
The volume at each frequency can be adjusted
from
–6dB to 0dB to +6dB in 1 dB steps.
Note
• You can select: “ 25Hz ”, “ 40Hz ”, “ 63Hz ”,
“ 100Hz ”, “ 160Hz ”, “ 250Hz ”, “ 400Hz ”, “ 630Hz ”,
“ 1000Hz ”, “ 1600Hz ”, “ 2500Hz ”, “ 4000Hz ”,
“ 6300Hz ”, “ 10000Hz ”, or “ 16000Hz ”. And for the
subwoofer, “ 25Hz ”, “ 40Hz ”, “ 63Hz ”, “ 100Hz ”, or
“ 160Hz ”.
• While the Direct listening mode is selected, the
equalizer settings have no effect.
Tip
• Low frequencies (e.g., 63Hz) affect bass sounds;
high frequencies (e.g., 16000Hz) affect treble
sounds.
3
Use
q
to select “Channel”, and then use
e
/
r
to select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to “
No ”
or “ None ” in the “ Speaker Configuration ”
(
➔
54 ).