Integra DTR-70.2, Инструкция по эксплуатации

Страница: 106 / 124

106
En
■
The beginning of audio received by an HDMI IN
can’t be heard
■
There’s no picture
■
There’s no picture from a source connected to
an HDMI IN
■
The on-screen menus don’t appear
■
The picture is distorted
■
The on screen display does not appear
■
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t light
■
The remote controller doesn’t work
Since it takes longer to identify the format of an
HDMI signal than it does for other digital audio sig-
nals, audio output may not start immediately. —
Video
Make sure that all video connecting plugs are pushed
in all the way. 17
Make sure that each video component is properly
connected. 18 , 19 ,
92
If your TV is connected to the HDMI output, set the
“
Monitor Out ” setting other than “ Analog ”, and
select “ - - - - - ” in the “ HDMI Input ” to watch com-
posite video, S-Video, and component video sources.
50 , 51
If your TV is connected to the
COMPONENT
VIDEO MONITOR OUT , MONITOR OUT S , or
MONITOR OUT V
, set the “ Monitor Out ” setting
to “ Analog ”, and select “ - - - - - ” in the “ Compo-
nent Video Input ” to watch composite video and
S-Video sources.
50
,
52
If the video source is connected to a component
video input, you must assign that input to an input
selector, and your TV must be connected to either
the HDMI output or
COMPONENT VIDEO MON-
ITOR OUT .
19 , 52
If the video source is connected to a composite video
input, your TV must be connected to the HDMI out-
put or the corresponding composite video output.
19
If the video source is connected to an HDMI input,
you must assign that input to an input selector, and
your TV must be connected to the HDMI output. 18 , 51
On your TV, make sure that the video input to which
the AV receiver is connected is selected. —
If you selected “ Both(Main) ” or “ Both(Sub) ” in the
“ Monitor Out ” setting, no picture may appear on
your TV that is connected to a secondary HDMI out-
put (not a priority HDMI output). In this case,
change the setting to “
Both ”.
—
Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not guaranteed. 114
When the “ Monitor Out ” setting is set to “ Analog ”,
and the “ Resolution ” setting is set to anything other
than “ Through ”, no video is output by the HDMI
outputs.
51
When the “ Resolution ” is set to any resolution not
supported by the TV, no video is output by the
HDMI outputs.
51
If the message “ Resolution Error ” appears on the
AV receiver’s display, this indicates that your TV
does not support the current video resolution and
you need to select another resolution on your DVD
player.
—
(Australian models) Specify the TV system used in
your area in the “ TV Format ”.
66
On your TV, make sure that the video input to which
the AV receiver is connected is selected. —
If your TV is connected to the analog outputs, set the
“
Monitor Out ” setting to “ Analog ”.
50
(Australian models) Specify the TV system used in
your area in the “ TV Format ”.
66
If you select other than “ Analog ” in the “ Monitor
Out ” setting, the immediate display will not appear
when the input signal from the COMPONENT
VIDEO IN is output to a device connected to the
COMPONENT VIDEO MONITOR OUT .
50
Depending on the input signal, the on screen display
may not appear when the input signal from the
HDMI IN
is output to a device connected to the
HDMI output.
66
Tuner
Relocate your antenna. —
Move the AV receiver away from your TV or com-
puter. —
Listen to the station in mono. 32
When listening to an AM station, operating the
remote controller may cause noise. —
Passing cars and airplanes can cause interference. —
Concrete walls weaken radio signals. —
If nothing improves the reception, install an outdoor
antenna. —
Remote Controller
Before operating this unit, be sure to press
Receiver .
—
Make sure that the batteries are installed with the
correct polarity. 4
Install new batteries. Don’t mix different types of
batteries, or old and new batteries. 4
Make sure that the remote controller is not too far
away from the AV receiver, and that there’s no
obstruction between the remote controller and the
AV receiver’s remote control sensor. 4
Make sure that the AV receiver is not subjected to
direct sunshine or inverter-type fluorescent lights.
Relocate if necessary. —
If the AV receiver is installed in a rack or cabinet
with colored-glass doors, the remote controller may
not work reliably when the doors are closed. —
Make sure you’ve selected the correct remote con-
troller mode.
11
,
99
When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected. —
Make sure you’ve entered the correct remote control
code.
98
Make sure to set the same ID on both the AV receiver
and remote controller.
67