Infors HT Ecotron Скачать руководство пользователя страница 68

Страница: 68 / 93

Ecotron - Incubation Shaker

Rectifying Faults

Page

03 May 2018

Fault

The shaker drive accelerates too quickly or runs too fast.

Possible cause

Measures

Personnel

Error when measuring the ro-

tation speed.

Switch the equipment off and then on again.

Operator

The drive control system is

defective.

Contact your local Infors representative and re-

place the control rack (see chapter 10.2, page

73).

Operator

Faults related to the “Temperature” parameter

Fault

The temperature fails to reach the desired setpoint.

Possible cause

Measures

Personnel

The heating is not switched

on.

Activate the “Temperature” parameter.

Operator

The setpoint is set too low.

Raise setpoint.

Operator

The ambient temperature

does not meet the require-

ments.

see chapter 6.1, page 41

Operator

Door not closed completely.

Close door completely.

Operator

Cooling fins dusty.

Clean the cooling fins.

Operator

Error during temperature

measurement.

Check the function of the temperature sensor. In

case of a defect, contact your local Infors repre-

sentative.

Operator

Heater fan not working.

Contact your local Infors representative and re-

place the control rack (see chapter 10.2, page

73).

Infors service techni-

cian or licensed dealer

INFORMATION

Re-measuring the temperature only provides reliable information

when using calibrated measuring tools, and only if they are used

at points specified by Infors. Measurements taken at undefined

points in the casing will not produce any usable data.
For information about temperature measuring, contact your local

Infors representative or request a quote for calibrating the pa-

rameters.

Содержание Ecotron






























































































Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды

Infors HT Ecotron, Руководство по эксплуатации

Результаты поиска

Содержание Ecotron

Отзывы:

Похожие инструкции для Ecotron

Бренды по названию

Популярные бренды